-
Igorzp
Member
- Звідки: Запорожье
Повідомлення
15.06.2011 19:16
H/W Monitor —Chassis Intrusion— Disabled
-
andrey.nk
Member
- Звідки: Николаев
Повідомлення
15.06.2011 20:26
а как плата определяет — открыт корпус или закрыт?
-
Igorzp
Member
- Звідки: Запорожье
Повідомлення
15.06.2011 20:29
andrey.nk, датчик используется.Но я с ними никогда лично не сталкивался
-
doCENTik85
Advanced Member
- Звідки: Прилуки-Киев
Повідомлення
15.06.2011 21:04
Недавно собирал систему на этой мамке, тоже напрягало это сообщение при загрузке, в дефолте почемуто она включена только вот зачем? Еще один глюк — на плате есть только один разьем PS/2 и мышка подключенная к нему определялась ровно через раз после перезагрузки.
-
StreetFIGHTER2000
Member
- Звідки: Украина
Повідомлення
16.06.2011 00:42
тоже сталкивался с этой фигней… Некоторые корпуса имеют специальный контакт налевой крышке, который подключается проводом к матери, поэтому в целях безопастности он не дает включится компу когда открыта боковая крышка.
изначально на этом контакте на матери стоит перемычка, возможно она спала. Поищите этот двухпиновый разьем на матери , он должен быть подписан как chassis intrussion и поправьте на нем перемычку либо закоротите его. Он будет похож на разьем для подключения вентидяторов только двухпиновый, быстрее его можно найти по схеме в инструкции матери.
-
Imales
Member
Повідомлення
17.06.2011 01:29
Igorzp:H/W Monitor —Chassis Intrusion— Disabled
Или
Case Open Warning
Chassis Intrusion
Chassis Intrusion Detect
Intruder Detection
И может не H/W Monitor
Пускай сначала скажет версию BIOS
-
Igorzp
Member
- Звідки: Запорожье
Повідомлення
17.06.2011 06:40
Imales, если открыть руководство для пользователя, то можно увидеть в каком разделе размещается данная настройка.
-
Imales
Member
Повідомлення
18.06.2011 07:50
Igorzp:если открыть руководство для пользователя, то можно увидеть в каком разделе размещается данная настройка.
Так не честно.Ты воспользовался подсказкой.Ты нашел manual для мамки.В следующий раз,давай играть по правилам.(не пользуясь интернетом)
-
zp_jogamax
Junior
- Звідки: Запорожье
Повідомлення
19.06.2011 15:56
В биосе было ровно вот так H/W Monitor —Chassis Intrusion— Disabled
в мануале не было ничего про это
в гугле были советы воспользоваться гуглом или поискать шнурок к корпусу
-
-stan-
Member
- Звідки: Канатоп
Повідомлення
19.06.2011 16:10
zp_jogamax:в гугле были советы воспользоваться гуглом
о да
- Forum
- Hardware
- Motherboard Processor & RAM
- Error Message «Warning! Your chassis has been opened»
-
Error Message «Warning! Your chassis has been opened»
Hi Everyone!
I have a acer aspire m1201 and it gives me this error message: chassis has been opened press f1 to continue.
Can anyone help with it??
Please Help…!
-
Re: Error Message «Warning! Your chassis has been opened»
You may just have to reset the CMOS, but I’m sure there’s gotta be a setting in the bios, dig deep or better yet, go to the Acer tech support site first and look it up for your model/serial #.
OR
In the bios, there is an option to disable open case alert. And it will ignore its open and run normally. What mobo and bios version do you have?
OR
Do you have the manual for your motherboard, it shows where the settings are. If you don’t you should be able to download a PDF version from manufacturer’s website. I’ve already seen a couple online, and it refers to the as Chassis Intrustion Detection or Chassis Intrusion Notification.
-
Re: Error Message «Warning! Your chassis has been opened»
Here is the solution. I had the same problem.
Chassis Warning :
«Warning your chassis has been opened. Press F1 to continue. Press Del to enter setup menu.»
Resolution :
- Enter Bios
- Goto Intergrated Peripherals
- Goto Onboard I/O setup
- Find «Chassis Opened warning»
- Set to “Disable”
- Press F10 to save and exit changes
- That all there is too it.
-
Re: Error Message «Warning! Your chassis has been opened»
TRY THIS :
- Unplug, remove the processor, the battery
- Quickly clear cmos jumpers (? Unless it wishes to say remove the cmos jumpers) at least 20 seconds while pressing the button …
- Leave the state at least 30 minutes
- Then reinstall (the processor and battery, I presume), restart
-
Re: Error Message «Warning! Your chassis has been opened»
I know this is an old thread, but just to save some confusion for some people who may have trouble with this:
In the BIOS if you are unable to find the «Chassis Opened Warning» anywhere, you need to go to PC Health Status and change the «Intruder Detection» option to Reset. Then you’re good to go!
This was driving me crazy for about half an hour.
Similar Threads
-
Replies: 7
Last Post: 23-02-2012, 08:16 PM
-
Replies: 6
Last Post: 07-07-2011, 09:47 PM
-
Replies: 5
Last Post: 19-04-2011, 08:54 AM
-
Replies: 3
Last Post: 30-07-2009, 09:43 PM
-
Replies: 5
Last Post: 02-03-2009, 11:40 PM
Tags for this Thread
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
by
·
Published April 22, 2014
· Updated May 30, 2018
if your Acer Desktop pc is showing the following error message “Warning!! Your computer case has been opened ” press F1 top continue , its easy to resolve, the cause of this error case sensor has stopped working or not seating properly ,
Solution is go in to bios by hitting F2 on start up , and go to bios security features menu
as shown in the image below
Warning!! Your computer case has been opened |
then on the next screen,go to Chasis Opened Warning , hit enter and chose cleared and then chose disable,
as show in the image below.
Warning!! Your computer case has been opened |
After that no chassis message will appear
Tags: AcerAcer Chassis OpenChasesChases WarningChasses WarningDesktop RepairfixedsolutionsolvedWarningWarning!! Your computer case
Mutahhar Bashir
Passionate blogger, have excellent problem solving skills, quick learner, love to accomplish difficult tasks, improving my skills while helping others through this blog.
You may also like…